Lanier Worldwide, Inc.
2300 Parklake Dr., N. E.
Atlanta, GA 30345-2979
Emergency Telephone: (800) 526-4371
MATERIAL SAFETY DATA SHEET
Section 1: Chemical Product and Company Information
Identity:
Developer for 5112
MSDS No.
FX-067
Product ID: 480-0007 Issued:
02/06/2004
Synonyms
& Common
Names:
Uses:
Chemical
Formula:
Black Developer for 5112, 4900
Lanier
Lanier 5112, 4900
Mixture
Supersedes:
Date:
Prepared by:
Approved by:
European Contact:
01/11/2001
02/06/2004
Lanier Worldwide, Inc.
Larry Choskey, EH&S Manager, (770) 496-9500
Lanier Worldwide, Inc.
Walter Fricke, Manager, Safety &
Environment
Im Taubental D-41468 Neuss, Germany
+49-2131-387-177
Section 2: Composition / Information on Ingredients
PERCENT CAS No. EXPOSURE LIMITS SOURCE
Ferrite 95 1309-37-1 N/a N/a
1317-38-0 N/a N/a
1314-13-2 15mg/m
3
10mg/m
3
OSHA PEL ACGIH TWA
Styrene acrylic polymer
*PEL as the product: 15mg/m
3
(total dust), 5mg/m
3
(respirable dust)
*TLV as the product: 10mg/m
3
(total dust), 5mg/m
3
(respirable dust)
Section 3: Hazards Identification
HMIS Rating:
FLAMMABILITY = 1 HEALTH = 1
REACTIVITY = 0 SPECIAL = none
Health Hazards (Acute, Chronic, Immediate and Potential): Minimum irritation to respiratory tract may occur as with exposure to any non-
toxic dust. May cause gasping if inhaled. Inhalation should be avoided. May cause temporary eye discomfort.
Health Hazards of Long Term exposure (Chronic): A manufacturer sponsored chronic inhalation study in rats using a special test toner
revealed there w ere no lung changes at all in the lowest exposure level (1mg/m
3
), the most relevant level to potential human exposures. A very
slight degree of fibrosis was noted in 25% of the animals at the middle exposure level (4mg/m
3
), while a slight degree of fibrosis was observed
at the highest exposure level (16mg/m
3
) in all animals. These findings are attributed to “Lung Overloading”, a generic response to excessive
amount of any dust retained in the lungs for a prolonged interval. The special test toner was ten times more respirable than commercially
available toner to comply with EPA testing protocol and would not function properly in Xerographic equipment.
This product contains no known hazardous materials as defined by the OSHA Hazard Communication Standard 29 CFR 1910.1200.
Section 4: First Aid Measures
Inhalation:
Remove to fresh air if effects occur. Gargle with
water. Get medical attention if needed.
Eye Contact:
In case of contact, immediately flush eyes with
water for 15 minutes. Get medical attention if
needed.
Skin Contact: Wash with soap and water. Ingestion:
Dilute stomach contents with several glasses
of water. Get medical attention if needed.
Section 5: Fire Fighting Measures
Suitable extinguishing media: CO
2
, dry chemical, foam or water.
Extinguishing media which may not be used for safety reasons: none
Unusual Fire and Explosion Hazards: Toner material, like most
organic material in powdered form, is capable of creating a
dust explosion.
Flammability: Non-flammable solid The decomposition products are CO, CO
2
, and No
x
. Avoid inhalation of smoke.
Special protective equipment for fire fighters: none
UEL: n/a LEL: n/a
Section 6: Accidental Release Measures
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji